Author Topic: Little Eric... (Read 6123 times)

bedlamite · « **Reply #25 on:** May 13, 2008, 02:41:54 AM »

A few years ago I sent the new kid at work to the tool room for the aluminum magnet.

The Annoyed Man · « **Reply #26 on:** May 13, 2008, 11:10:43 AM »

What... you used the one you fell for? Tongue

bedlamite · « **Reply #27 on:** May 13, 2008, 01:55:55 PM »

In your dreams putz

The Annoyed Man · « **Reply #28 on:** May 13, 2008, 02:19:55 PM »

By the way, you forgot your gigline last time you were up with Dozer...

280plus · « **Reply #29 on:** May 13, 2008, 02:23:18 PM »

Now now, fight nicely... laugh

The Annoyed Man · « **Reply #30 on:** May 13, 2008, 02:25:19 PM »

What you mean? This IS nicely! When we get mean, hard cover is ~~suggested~~ required for the spectators... Tongue

280plus · « **Reply #31 on:** May 13, 2008, 02:58:44 PM »

OK ok, just making sure... laugh

Stickjockey · « **Reply #32 on:** May 13, 2008, 03:24:13 PM »

ID 10 T error. Also known as a PEBCAC situation.

We got one FNG twice in the same day by asking her to go down to the freight house and get the pit stretcher for the Dash-8.

BTW, for those that don't know: PEBCAC= Problem Exists Between Computer And Chair.

bedlamite · « **Reply #33 on:** May 14, 2008, 02:37:14 AM »

Hey strings, let me know when you try to grease your brakes again, I'd like to watch.

The Annoyed Man · « **Reply #34 on:** May 14, 2008, 02:03:11 PM »

Um, that was Stenz. And it only happened because I wasn't paying attention to where he was going with the grease gun... Tongue

And remember: next time we have steak, you need to actually CHEW each piece. Just because Dozer can inhale it, doesn't mean you can! Tongue

Tallpine · « **Reply #35 on:** May 14, 2008, 03:01:40 PM »

Where can I find a left-handed metric crescent wrench ?

laugh

280plus · « **Reply #36 on:** May 14, 2008, 03:25:21 PM »

Quote from: Tallpine on May 14, 2008, 02:01:40 PM

Where can I find a left-handed metric crescent wrench ?

laugh

You mean the crescent hammer i think... grin

I love the looks I get, "Would you hand me that crescent hammer please?" laugh

Mabs2 · « **Reply #37 on:** May 14, 2008, 05:26:38 PM »

"Pass my that hammer-four."
"What's a hammer-four?"
"If you don't know what a hammer's for..."

Scout26 · « **Reply #38 on:** May 14, 2008, 05:27:44 PM »

Quote from: Tallpine on May 14, 2008, 02:01:40 PM

Where can I find a left-handed metric crescent wrench ?

laugh

Sorry all we got are left handed socket sets.

Modifiedbrowning · « **Reply #39 on:** May 14, 2008, 06:01:07 PM »

Left handed lighter.
Sleeveless jacket.

wmenorr67 · « **Reply #40 on:** May 14, 2008, 08:13:30 PM »

A henweigh.

Tallpine · « **Reply #41 on:** May 15, 2008, 07:01:12 AM »

Quote

You mean the crescent hammer i think...

Gee, and I thought that one was my inside joke shocked

I used to work (logging) with this guy what was - well, not very sharp. One time he was trying to get a clevis unscrewed and it was too tight to turn out by hand, so I handed him up a crescent wrench. He immediately began trying to tap the flat end of the clevis pin to get it to turn, instead of using it as a wrench rolleyes

From that moment forward, "crescent hammer" was the new term laugh

grislyatoms · « **Reply #42 on:** May 16, 2008, 07:30:52 AM »

Quote

BTW, for those that don't know: PEBCAC= Problem Exists Between Computer And Chair.

We refer to that as a "biological interface problem". grin

RandyinArizona · « **Reply #43 on:** May 21, 2008, 03:18:00 PM »

or the muffler bearings, fuel pump belt, and winter air in snow tires...

Actually some foreign cars do have fuel injection pump belts.

News:

Author Topic: Little Eric... (Read 6123 times)