Author Topic: I gotta get me some bull bars for the Battlecruiser...  (Read 1879 times)

Bogie

  • friend
  • Senior Member
  • ***
  • Posts: 10,719
  • Hunkered in South St. Louis, right by Route 66
    • Third Rate Pundit
I gotta get me some bull bars for the Battlecruiser...
« on: June 29, 2022, 10:39:53 AM »
This is one of my favorite hijacking vids...
 
https://twitter.com/desertlife88/status/1541944549873836032

When I was doing the expedited transport thing, I had some youts throw an orange barrel in front of the truck, expecting me to stop at a convenient wide place just ahead. With plenty of places for people to stand in the shadows. That was a nope...
Blog under construction

WLJ

  • friends
  • Senior Member
  • ***
  • Posts: 32,787
  • On Patrol In The Epsilon Eridani System
Re: I gotta get me some bull bars for the Battlecruiser...
« Reply #1 on: June 29, 2022, 10:43:22 AM »
But if you start adding more armor wouldn't that make it a Battleship?


Exit stage left
“Liberals claim to want to give a hearing to other views, but then are shocked and offended to discover that there are other views.”
― William F. Buckley

“The Party told you to reject the evidence of your eyes and ears. It was their final, most essential command.”
― George Orwell, 1984

“Those who believe without reason cannot be convinced by reason.”
― James Randi

Bogie

  • friend
  • Senior Member
  • ***
  • Posts: 10,719
  • Hunkered in South St. Louis, right by Route 66
    • Third Rate Pundit
Re: I gotta get me some bull bars for the Battlecruiser...
« Reply #2 on: June 29, 2022, 10:50:33 AM »
Only if I drive under an overpass near my house during a really good downpour...
Blog under construction

WLJ

  • friends
  • Senior Member
  • ***
  • Posts: 32,787
  • On Patrol In The Epsilon Eridani System
Re: I gotta get me some bull bars for the Battlecruiser...
« Reply #3 on: June 29, 2022, 11:15:12 AM »
Only if I drive under an overpass near my house during a really good downpour...

“Liberals claim to want to give a hearing to other views, but then are shocked and offended to discover that there are other views.”
― William F. Buckley

“The Party told you to reject the evidence of your eyes and ears. It was their final, most essential command.”
― George Orwell, 1984

“Those who believe without reason cannot be convinced by reason.”
― James Randi

MechAg94

  • friend
  • Senior Member
  • ***
  • Posts: 34,660
Re: I gotta get me some bull bars for the Battlecruiser...
« Reply #4 on: June 29, 2022, 11:15:15 AM »
But if you start adding more armor wouldn't that make it a Battleship?


Exit stage left
I think it would be more of an armored cruiser. 

I does highlight the usefulness of a truck and/or something with a strong engine rather than a tiny commuter car.  My Toyota Tacoma might be able to handle that.  Not certain. 
“It is much more important to kill bad bills than to pass good ones.”  ― Calvin Coolidge

Bogie

  • friend
  • Senior Member
  • ***
  • Posts: 10,719
  • Hunkered in South St. Louis, right by Route 66
    • Third Rate Pundit
Re: I gotta get me some bull bars for the Battlecruiser...
« Reply #5 on: June 29, 2022, 11:36:34 AM »
You wouldn't want your airbags to blow... I'm guessing that was a midsize truck, probably hauling something of value.
Blog under construction

230RN

  • I saw it coming.
  • friend
  • Senior Member
  • ***
  • Posts: 19,386
  • But they're SUPPOSED to be "military-style."
Re: I gotta get me some bull bars for the Battlecruiser...
« Reply #6 on: June 30, 2022, 07:00:34 PM »
This is one of my favorite hijacking vids...
 
https://twitter.com/desertlife88/status/1541944549873836032

When I was doing the expedited transport thing, I had some youts throw an orange barrel in front of the truck, expecting me to stop at a convenient wide place just ahead. With plenty of places for people to stand in the shadows. That was a nope...

Hilarious.

Swift and terrrible Justice.

Ought to be applied more frequently, maybe.

AJ Dual

  • friends
  • Senior Member
  • ***
  • Posts: 16,162
  • Shoe Ballistics Inc.
Re: I gotta get me some bull bars for the Battlecruiser...
« Reply #7 on: July 01, 2022, 03:42:21 PM »
Ranch Hand and ARB seem to be the go-to standards.
I promise not to duck.

BobR

  • Just a pup compared to a few old dogs here!
  • friend
  • Senior Member
  • ***
  • Posts: 7,614
Re: I gotta get me some bull bars for the Battlecruiser...
« Reply #8 on: July 01, 2022, 03:56:43 PM »
Any self identifying Battlecruiser needs nothing but the best, Feral Thumper Bullbars.

https://boomerbullbars.typepad.com/boomer-bullbars/2020/07/ford-f350.html

;)

bob

Bogie

  • friend
  • Senior Member
  • ***
  • Posts: 10,719
  • Hunkered in South St. Louis, right by Route 66
    • Third Rate Pundit
Re: I gotta get me some bull bars for the Battlecruiser...
« Reply #9 on: July 01, 2022, 04:16:49 PM »
FWIW, if you live in deer country, reinforce the roof of your truck a bit, then run 1/4" or 3/8" steel cable TIGHT from each front corner bull bar to the same side corner of the roof - If Bambi leaps, bambi is more likely to get swept aside, rather than go through the windshield.
Blog under construction

HeroHog

  • Technical Site Pig
  • Administrator
  • Senior Member
  • *****
  • Posts: 8,232
  • It can ALWAYS get worse!
    • FaceButt Profile
Re: I gotta get me some bull bars for the Battlecruiser...
« Reply #10 on: July 02, 2022, 01:13:41 AM »
I might not last very long or be very effective but I'll be a real pain in the ass for a minute!
MOLON LABE!

dogmush

  • friend
  • Senior Member
  • ***
  • Posts: 14,771
Re: I gotta get me some bull bars for the Battlecruiser...
« Reply #11 on: July 02, 2022, 06:54:38 AM »
FWIW, if you live in deer country, reinforce the roof of your truck a bit, then run 1/4" or 3/8" steel cable TIGHT from each front corner bull bar to the same side corner of the roof - If Bambi leaps, bambi is more likely to get swept aside, rather than go through the windshield.

Or only half of Bambi goes through the windshield.

Bogie

  • friend
  • Senior Member
  • ***
  • Posts: 10,719
  • Hunkered in South St. Louis, right by Route 66
    • Third Rate Pundit
Re: I gotta get me some bull bars for the Battlecruiser...
« Reply #12 on: July 02, 2022, 07:18:27 AM »
One assumes you are already proceeding at a "less than cutting" speed...
Blog under construction

WLJ

  • friends
  • Senior Member
  • ***
  • Posts: 32,787
  • On Patrol In The Epsilon Eridani System
Re: I gotta get me some bull bars for the Battlecruiser...
« Reply #13 on: July 02, 2022, 10:44:18 AM »
I think it would be more of an armored cruiser. 


How about a protected cruiser?  :P
“Liberals claim to want to give a hearing to other views, but then are shocked and offended to discover that there are other views.”
― William F. Buckley

“The Party told you to reject the evidence of your eyes and ears. It was their final, most essential command.”
― George Orwell, 1984

“Those who believe without reason cannot be convinced by reason.”
― James Randi

Kingcreek

  • friend
  • Senior Member
  • ***
  • Posts: 3,753
Re: I gotta get me some bull bars for the Battlecruiser...
« Reply #14 on: July 02, 2022, 11:24:43 AM »
Height of bumper armor and ground clearance also matter.
I hit a deer at 80mph in my F250 and it went under the truck.
The steel bumper on my Jeep is about mid femur on an upright 6’ humanoid.
What we have here is failure to communicate.

230RN

  • I saw it coming.
  • friend
  • Senior Member
  • ***
  • Posts: 19,386
  • But they're SUPPOSED to be "military-style."
Re: I gotta get me some bull bars for the Battlecruiser...
« Reply #15 on: July 02, 2022, 11:33:38 AM »
Height of bumper armor and ground clearance also matter.
I hit a deer at 80mph in my F250 and it went under the truck.
The steel bumper on my Jeep is about mid femur on an upright 6’ humanoid.

Ahem.  That is not a bumper.  That is a trunker.

dogmush

  • friend
  • Senior Member
  • ***
  • Posts: 14,771
Re: I gotta get me some bull bars for the Battlecruiser...
« Reply #16 on: July 02, 2022, 05:15:48 PM »
Height of bumper armor and ground clearance also matter.
I hit a deer at 80mph in my F250 and it went under the truck.
The steel bumper on my Jeep is about mid femur on an upright 6’ humanoid.

Also depends on the local deer.  My F150's steel number and lift ensure the adorable little things FL calls deer would go under it.  Bigger deer might stay in the grill.

Kingcreek

  • friend
  • Senior Member
  • ***
  • Posts: 3,753
Re: I gotta get me some bull bars for the Battlecruiser...
« Reply #17 on: July 02, 2022, 06:40:42 PM »
I was in the middle of South Dakota when I hit that one. It was close to 200 pounds if I’m any judge in the headlights for a split second at 80mph and 0 dark 30. It bent my front tie rod causing severe toe in and exploded on the front axle. Parts of it were hanging from the outside rear view mirrors and strung out thru the wheels. Also parts packed around the exhaust manifold and cat converter and stinking bad the next day.
What we have here is failure to communicate.

kgbsquirrel

  • APS Photoshop God
  • friend
  • Senior Member
  • ***
  • Posts: 5,466
  • Bill, slayer of threads.
Re: I gotta get me some bull bars for the Battlecruiser...
« Reply #18 on: July 03, 2022, 12:11:58 AM »
You wouldn't want your airbags to blow... I'm guessing that was a midsize truck, probably hauling something of value.

A guarded toggle switch to cut-out the airbags would probably be worthwhile.

Bogie

  • friend
  • Senior Member
  • ***
  • Posts: 10,719
  • Hunkered in South St. Louis, right by Route 66
    • Third Rate Pundit
Re: I gotta get me some bull bars for the Battlecruiser...
« Reply #19 on: July 03, 2022, 07:45:42 AM »
I've tagged two deer, and one black angus that decided that the middle of a country road at 3am was a good place to nap.
 
All three were totals, but still somewhat drivable to get to the rental place.
 
At least I wasn't the idiot who decided to drive a railroad right-of-way, despite signs, and get a wheel in a hole - and then just stand around until a train came along and zapped the vehicle, and all the test equipment that they didn't pull out while they were standing around.
Blog under construction